Greystone 32-Inch Electric Fireplace # 324-000076 has a shipping weight of 34-lbs, but a few pounds will be attributed to the carton and packing materials so figure the actual net weight of the unit itself as 32-lbs.
This unit plugs into a standard household type AC power outlet and it will best be installed on its own 15-amp circuit since it will draw over 12-amps all by itself. The included AC cord is 6-feet long and it is on the right-hand side of the fireplace.
If you need an extension... view full answer...
Curt's Trailer Hitch Receiver # C11272 for the 2012 - 2013 Mini Cooper Hardtop with single exhaust is a light-duty Class I hitch that really should not be used with any sort of hitch adapter.
The reason is that on any hitch on any vehicle hitch extensions like # HTAD, # HT5R and # HES6 move the actual load far enough away from the hitch tube to increase the leverage and stress on it. These adapters also tend to allow for more random motion of whatever is mounted in them and this again... view full answer...
I reached out to the manufacturer who told me the HydraStar Electric Over Hydraulic Actuator for Disc Brakes # HBA16 has a fluid capacity of 10 oz.
They told me that was going to be more than ample capacity to allow for brake pad wear once the brakes are bled and the unit is topped off.
I have added links to video reviews of this actuator for you to take a look at. view full answer...
The correct B and W Turnoverball Gooseneck Hitch for your 1998 Dodge Ram 1500 is the part # BWGNRK1394 and the measurements to use vary depending on your bed length. You'll want the hole centered from left to right but from the rear edge of the truck bed the hold would be 48-3/8 inches if you have a long bed or 44-3/8 inches if you have a short bed. I attached a picture that I took from the install instructions which shows this as well. view full answer...
The Curt gooseneck hitch part # C60720 only fits the 6-1/2 foot and 8 foot bed models of the 2014 Ford F-150 like yours so that is why they only list a long and short bed measurement for the ball hole. For the long bed trucks the ball hole will get drilled 96 inches back from the truck cab and for the short bed trucks it will be 35 inches. The dimension needs to be centered from left to right as well. view full answer...
On the Lippert # LC119226, the slot in question is 1/4 inch wide by 3/8 of an inch deep, on the # RVLG-HDL it measure 1/4 inch wide by 7/16 of an inch deep. You can see these photos in the photo I've provided. view full answer...
I checked with Yakima and the Holdup # Y02443 that you referenced can fit bike tires up to 3 inches in width. It looks like it's been updated a couple times which may have been why there was a different tire width listed. view full answer...
According to Greystone, the rough opening necessary to install the # 324-000068 will be 26-1/4" wide x 20-1/2" tall x 5-3/8" deep and the overall dimensions are 28-3/8" wide x 21-3/8" tall x 5 1-2" deep. view full answer...
As long as the weight of your carrier and chair is less than 200 lbs the Roadmaster Drop Adapter part # RM-076 will work well for you as it gives you the drop you need. It also cuts the capacity of your hitch by 50 percent but since it's a truck that shouldn't be a problem. view full answer...
I looked through all of our available manual A-Frame trailer jacks and the option with the shortest retracted bracket height is the etrailer.com A-Frame # TJA-2001-B. The retracted bracket height is right at 5-1/8 inches from the bracket and it has a weight capacity of 2,000 pounds.
It doesn't come with a wheel caster available. view full answer...
On the Swagman Platform-Style Bike Rack, # S64663, The center of your bike will sit 9 inches away from the hitch pin hole on your trailer hitch and approximately 11 inches away from your tailgate. We haven't had the chance to test this bike rack on a Colorado yet, but these dimensions should give you an idea of how it will fit.
If you don't think that will work for you, then I suggest looking at the Hollywood Racks Trail Rider # HR200Z. This bike rack will extend your bike out another... view full answer...
The 225 lb weight capacity of the Curt Premium 5-Bike Rack # C18065 is not referring to hitch weight, just the weight of the bikes.
Keep in mind you will need Bike Frame Adapter Bar # HRBA-PRO if you plan on carrying a bike that is dual-suspension, has a step-through frame or you want to carry a small children's bike. The bar will give those bikes a horizontal mounting point so they can be carried by the rack.
I have added links to video reviews for you to check out as well of the adapter... view full answer...
In regards to the CE Smith Single Axle Trailer Fender part # CE19503, this fender is designed to be used with 13" diameter wheels. The manufacturer does not provide specific measurements of the opening inside but rather the size of wheel that the opening is designed to work with. I have attached a list of options below as well for different size wheels.
In regards to the inside opening, if you subtract the size of the step on each side from the overall length which we do provide, the... view full answer...
The 4 on 4" bolt hole pattern for the Loadstar ST175/80D13 Bias Trailer Tire with 13" White Wheel # AM3S030 is a little bit larger than a 4 on 100mm bolt hole pattern so they aren't interchangeable unfortunately.
We typically try to avoid recommending wheels spacers simply because it means the tire/wheel won't be riding on the hub like it was meant to. What I recommend doing is looking for a wheel with an offset so that the wheel sits where it needs to, but can also provide some clearance.... view full answer...
I contacted Roadmaster and they were able to confirm that the Roadmaster Direct-Connect Base Plate Kit for the 2019 Chevrolet Equinox, part # RM-523193-5, measures 15-3/4 inches from the ground to the center of the arms.
You'll want to measure your hitch height on the RV. If the difference in height between your Equinox and the RV is more than 3 inches, you will need to use a high low adapter. I've linked our selection at the bottom of the page for you as well as our article on how to... view full answer...
The length of the male plastic piece of the Replacement Tie-Down for Extang Solid Fold 2.0 Hard Tonneau Covers # EX1024 is 1-1/2 inches. This is the correct replacement tie-down for the Solid Fold 2.0 Series 83-xxx covers.
I have added a link below to a video review for you to check out as well. view full answer...
The diameter of the bolts that works with the CE Smith Padlock Brackets for Spare Tire Carriers # CE26002Z-2 are 7/16 inch.
The brackets are designed to work with the CE Smith Spare Tire Carrier for Trailers - Steel - 4- and 5-Lug Wheels - 8-3/8" Long # CE22007Z-11050-2 and 12-1/4" Long # CE22011Z-11050-2.
I have added a link below to a video review for you to check out as well of the CE Smith Padlock Brackets for Spare Tire Carriers # CE26002Z-2. view full answer...
When looking at weight capacities between a hitch and a cargo carrier you always want to go by the lowest number between the two. The 17x46 Curt Cargo Carrier Item # C18145 has a weight carrying capacity of 500lbs however; the Curt Trailer Hitch Receiver Item # C12091 on your 2014 Ford Fusion has a max tongue weight of 350lbs. Even though the cargo carrier can handle 500lbs you want to go by the 350lb max tongue weight of the hitch receiver.
If the hitch could handle 500lbs and the cargo... view full answer...
The upright portion of the # AM3410 adjustable ball mount that the ball platform slides up and down upon measures 9-1/16 inches in height, as shown in the provided photo.
In relation to the inside top of the receiver tube, the # AM3410 offers a maximum rise of 6-1/2 inches and a
maximum drop of 5-1/2 inches.
I've linked to a product video featuring the # AM3410 adjustable ball mount. view full answer...
So there are a couple of front-mounted trailer hitch receivers that fit your 2020 Ram 2500, and they do have different weight capacities, and different heights as well.
The highest capacity at 1000 lbs vertical load (like tongue weight) and 10,000 lbs line pull is the EcoHitch Hidden Front Mount Trailer Hitch Receiver # EH37FR.
The EcoHitch is not the lowest height, however, as it sits about an inch higher than the next option, which is from Curt. The Curt hitch does have a lower capacity... view full answer...
Go To Results